Kent · Extract fan repair and replacement
Walmer extract fan repair
Specialist extract fan repair for Walmer: diagnosis first, then a fixed quote, the work and a report with pictures. Ask us for a fixed quote.
- A failed fan that needs a replacement
- A fan that won’t start at all
- A worn or slipping fan belt
Extract fan repair for kitchens and businesses in Walmer
Grease is hard on extract fans. A coated impeller spins unevenly and the vibration wears out bearings and fixings. That is why we check the grease whenever we work on a fan and can arrange a TR19® clean of the whole system at the same time. Typical jobs include a humming noise from the fan motor and an extract that vibrates through the ductwork, across roof and wall fans, kitchen extract fans and belts and pulleys.
Around a place like Walmer, a pub, café or care home kitchen with a failed fan cannot carry on cooking as normal. Our 24/7 emergency line is there for exactly that.
The paperwork matters as much as the work. You get a written report with photos after every visit, covering the work done, any areas we couldn’t access and a recommended next date. Keep it with your fire safety records so it’s to hand when an insurer or inspector asks.
- Location
- Walmer (CT14)
- Wider area
- Kent
- Paperwork
- Written report with photos
- Quotes
- Fixed quote, typically within a working day
- Working hours
- Out of hours as standard, 24/7 emergency line
- Phone
- 0345 646 2711
- Last updated
- 30 October 2026
What happens if it’s left?
In kitchens with an interlocked gas supply, no extract can mean no cooking. Even without an interlock, cooking without extraction isn’t sensible, so a failing fan is worth dealing with early. Systems on quieter sites still build up dirt and wear, just more slowly.
No two sites are the same, so each one gets its own fixed quote. Size, access, the condition of the system and when we can work all play a part.
Why book with us
- A single point of contact for sites across the South East and London
- Fully insured
- Every job surveyed first
- A fixed price before any work starts
When a fan fails in Walmer
Sea air reaches Walmer, which sits within about 1 mile of the coast. Salt air is hard on fan housings, motors and fixings on roofs and outside walls. Food Standards Agency data counts about 49 restaurants, cafés and works canteens and about 24 sandwich bars and takeaways within 1.5 miles or so of the middle of Walmer. Wherever they cook under a canopy, a failed extract fan stops the kitchen. Environmental health officers from Dover council inspect food businesses in Walmer. A kitchen with no working extract can fall short of the suitable and sufficient ventilation food hygiene rules expect. A kitchen without a working fan has a problem to fix quickly.
For a takeaway near Walmer station, a fan that fails on a busy evening means turning customers away, and our emergency line runs 24/7. Hall kitchens near St Mary's Church, or anywhere around Walmer, often use their fans only now and then, and an idle fan can stick.
Walmer is about 6 miles north-east of Dover, in Kent. Sites in Walmer get the same service as everywhere we cover: a survey first, a fixed quote, work timed around your hours and a report with pictures. Our Kent coverage runs to 922 places, Walmer among them. Maidstone is in our area too, about 38 miles from Walmer.
Postcode districts we cover here for extract fan repair: CT14. If you need extract fan repair at premises on Lawn Road, York Road and Grams Road or a nearby road, we can help. Walmer sits on or near the A258, so getting to you is simple for evening and night visits. We also cover the places around Walmer: Deal (1 mile north), Mill Hill (1 mile north-west), Great Mongeham (2 miles north-west), Sholden (2 miles north-west) and Ripple (2 miles west). We also work in nearby towns such as Canterbury (15 miles west), Margate (12 miles north), Dover (6 miles south-west), Folkestone (13 miles south-west), Ramsgate (9 miles north) and Broadstairs (11 miles north).
Landmarks near Walmer
Typical jobs here are in premises near Goodwin Academy and The Telegraph pub, among other places. For rail, the closest station is Walmer station, roughly 0.7 miles west of the centre. Nearby you’ll also find Kent Museum of the Moving Image (1.4 miles north) and Walmer Castle (within half a mile south-east).
FAQs for Walmer
Does the sea air around Walmer make a difference to extract fan repair?
It can. Walmer is within about 1 mile of the coast, and salt air speeds up corrosion. A fan housing that is rusting near the coast can fail sooner, so it’s worth catching early.
Do you work at weekends in Walmer?
Yes. We work evenings, overnight and at weekends. The site is handed back ready to open. Your opening times are the first thing we ask for.
Should the fan be cleaned as well as repaired?
A repair deals with the fan, not the grease in the rest of the system. If there’s grease on the fan, a full TR19® clean is worth booking, and we can arrange both.
Do you work with multi-site operators?
Yes. One number covers all your sites across London and the South East, and visits can be set on a regular cycle.
Which accreditations do you hold?
We hold CHAS, SafeContractor and ISO 9001, and we’re a BESCA Vent Hygiene Elite member, cleaning to BESA TR19® Grease. Vent Hygiene Elite is run by BESCA and independently audited.
Will you fit a new fan if ours can’t be repaired?
Yes, when repair does not make sense. We check the duct size and the extract the kitchen needs so we confirm that first.
Who is responsible for fire safety on the premises?
The Fire Safety Order 2005 calls them the responsible person: often the employer, owner or occupier. Landlords, facilities managers and managing agents can also hold responsibility.
How do you keep the site clean during the work?
With sheeting and covers, before anything else happens. The work is kept contained and leave the area clean.
What affects the cost of extract fan repair
A fixed price needs a few facts first. We look at:
- How big the system is
- Any permits to work or inductions
- How many systems or sites are involved
- Access, including roofs, risers and ceiling voids
One small site or a whole estate, we price it on the same basis: the work involved, the access and the timing. You’ll have a fixed price before work begins.
What we need to know
You do not need the technical terms. Just send:
- The paperwork from the last visit, if you have it
- When the site is open and when it’s quiet
- Problems your staff have spotted
- Where the site is and what kind of site it is
Need a price for extract fan repair? Please call us on 0345 646 2711 or email us and tell us about the site. We’ll talk you through the work and send you a fixed quote before you commit to anything.
For landlords and multi-site operators
Keeping records across a portfolio is half the battle. Each visit ends with a dated report and pictures, so you can show an insurer or inspector what was done at each site.
Landlords, managing agents and facilities managers book us, not only the businesses that use the systems. Where a system serves more than one tenant, such as a shared riser, it helps to agree who arranges the work, and we’re happy to quote for all of it.
Towns and villages near Walmer
More services for Walmer
What extract fan repair can’t fix
Not every problem is solved by extract fan repair, and we’d rather say so up front. It does not solve:
- Cooking smells reaching neighbours, which may need odour control
- Problems with the gas supply or its interlock valve
- Grease throughout the ductwork, which needs a full TR19 clean
If in doubt, ring 0345 646 2711, or email photos and we’ll say what we think before booking.
Parts of the system we cover
- Bearings
- Roof and wall fans
- Kitchen extract fans
- Belts and pulleys
- Fan housings
- Fan motors
Between visits
After the visit, a few habits help the work last:
- Never run the extract with filters missing
- Get a noisy fan checked rather than slowed down
- Report new noises from the fan early
- Write down when the fan misbehaves
Clean filters help a repaired fan stay that way. The less grease that reaches the fan, the longer its parts last and the quieter it runs.
Regular TR19 cleaning includes the extract fan. Keeping grease off the impeller is one of the simplest ways to protect it, so planned cleaning helps the fan last.
Signs you need extract fan repair in Walmer
Bearings wear out with heat and long hours. Worn bearings whine, rumble or grind and a seized bearing stops the fan.
Any of these means the system needs a check-up:
- A fan shaking on its mountings
- A fan running too slowly to clear the kitchen
- An extract fan that has stopped working
- A fan that keeps cutting out
If you run a school kitchen, at a school such as The Downs Church of England Primary School or nearby, a fan that is getting noisy is best repaired in the holidays before it fails in term.
Before booking anyone
- Whether the price is fixed
- What happens if part of the system cannot be accessed
- Whether the quote shows VAT
- How they set the interval to the next visit
What we do, step by step
Protection comes first: sheeting goes over floors and surfaces close to the work. Then we make the system safe and start. It takes a few hours on site, depending on the fault and the access to the fan, and we clear up before we go. We plan the journey to Walmer and bring what the job is likely to need.
- We agree a time to attend, out of hours if needed.
- The extract is switched off and the fan opened up.
- We inspect every moving part and the fixings.
- You hear whether repair or replacement makes sense, with a fixed quote.
- We complete the work and check the fan runs smoothly.
How to prepare
- Make sure equipment near the work can be switched off and left to cool
- Let us know when the site is closed or quiet
- Tell us where we can park and unload
How to get a quote
Getting a quote does not take long. Call or email with a few details and you’ll normally have a fixed price within one working day. Where a survey is needed, we arrange a time that suits the site.