Slough · Extract fan repair and replacement
Extractor fan repair in Fulmer
For extract fan repair in Fulmer, one call is all it takes: survey, fixed quote, work and sign-off. Fully insured, with CHAS, SafeContractor and ISO 9001.
- A fan that won’t start at all
- A fan running too slowly to clear the kitchen
- A fan worn beyond sensible repair
Why act early in Fulmer
Wherever the kitchen is, Fulmer included, the fan often sits on an outside wall or roof, where a rattle or a whine can be heard beyond the kitchen. Dealing with the fault brings the noise back down before neighbours notice. Systems in rural buildings are often out of sight and out of mind.
Several systems or sites on one quote often makes better use of the time. Mention every system or site you need covered and we will price it together.
Why us?
- In business since 2009
- A single point of contact for sites across the South East and London
- A BESCA Vent Hygiene Elite member, cleaning to BESA TR19® Grease
- Survey first, then a fixed quote
Read what affects the cost or our accreditations and certificates.
About our extract fan repair in Fulmer
Grease is hard on extract fans. A coated impeller spins unevenly and the vibration wears out bearings and fixings. That’s why we check the grease whenever we work on a fan, and a full TR19® clean can be booked alongside. The work covers bearings, roof and wall fans and fan housings, and common reasons people get in touch are vibration spreading from the fan into the ducts and a fan that won’t start at all.
A callout to a small place like Fulmer goes better when we know what we’re looking at: a photo of the fan, the details on its label and the access arrangements help us plan.
The report is your system’s health record: a dated account with pictures of everything we did. Grease extract cleans are also certificated to TR19® Grease through the BESCA VHE portal and sits alongside the report.
- Where
- Fulmer (SL3)
- Wider area
- Slough
- Paperwork
- Photo report after every visit
- Price
- A fixed price before we start
- When we work
- After hours by arrangement; emergencies any time
- Phone
- 0345 646 2711
- Last updated
- 30 October 2026
What else we do in Fulmer
What happens on the day
There’s very little for your team to do on the day. A contact on site lets us in at the agreed time and points us to the system, and we take it from there. Before we leave, the area is tidied and the paperwork follows. A few photos of the system help us make the most of a visit to a place like Fulmer.
- First, you tell us the symptoms: noise, shaking, weak extraction or no power.
- Power to the fan is isolated before we open the housing.
- The impeller, bearings, belts or drive, motor and mounts are all inspected.
- You hear what’s wrong and what it will cost, with a fixed quote, before we go ahead.
- We fix or replace the fan, then test it running before we leave.
Preparing for the visit
- Mention any parking or loading restrictions
- Clear the space around the work
- Tell us the best time to work, such as after service or at a weekend
Getting a quote
Photos are enough for some jobs, while others need a look on site. Big or complicated sites, and systems that are hard to see in photos, get a survey first. Either way, you get a fixed price before work begins.
Related advice
Managing agents and facilities teams in Fulmer
Managing agents often deal with us directly. Send the address, what’s needed and how access works, and we’ll send a fixed quote.
Records are where multi-site compliance often slips. Each visit ends with a dated report and photos, ready to show insurers, fire officers or EHOs.
Looking after it afterwards
Results last longer with the right care. Here’s what we suggest:
- Keep the grease filters clean and fitted
- Don’t cook with gaps in the filter bank
- Make sure staff know who to call if the fan fails
- Book regular TR19 cleaning, which includes the fan
Keep an ear on the fan after the repair. A new noise or vibration is worth reporting early rather than waiting for it to fail.
Noise is normally the first sign of a fan problem. Booking a check at this stage keeps it a planned job rather than an emergency during service.
When to call us in Fulmer
Not every problem is mechanical. Speed controllers, isolators and wiring can all fail, and a fan that won’t start isn’t always a dead motor.
Most sites get in touch when they notice something like this:
- A squealing belt on start-up
- An extract fan that rattles or knocks
- A humming noise from the fan motor
- Vibration spreading from the fan into the ducts
If you run a school kitchen, at a school such as Fulmer Infant School or nearby, a fan that is getting noisy is best repaired in the holidays before it fails in term.
What to look for in a quote
- Exactly which parts of the system are covered
- Whether inaccessible sections are listed on the report
- Whether the figure could change on the day
- What records you will receive afterwards
What staff can safely do
Day-to-day cleaning is something your team can do: wiping down canopy surfaces, cleaning filters and keeping a simple log. Inside the ducts, risers and fan is specialist work, and that’s where we come in.
Staff cleaning does not replace a specialist visit; it supports it. Clean filters and tidy surfaces slow the build-up, but the parts you cannot see still need a specialist at the right interval.
Extract fans in Fulmer
Food Standards Agency data counts about 7 cafés, restaurants and staff canteens within roughly a mile and a half of the centre of Fulmer. Wherever they cook under a canopy, a failed extract fan stops the kitchen. It’s Buckinghamshire council that sends environmental health officers to food businesses in Fulmer. Ventilation is part of food hygiene law, which expects it to be suitable and sufficient. A kitchen without a working fan has a problem to fix quickly. Fulmer, about 20 miles from central London, is within our usual area. The visit is fixed around your opening hours, not ours.
A fan that rarely runs, like one in a hall kitchen near Church of St James or elsewhere in Fulmer, can seize between uses.
Fulmer is about 4 miles north-east of Slough, in Slough. We carry out extract fan repair for businesses, landlords and public buildings in Fulmer and the rest of Slough. Fulmer is one of 31 towns, villages and districts in Slough we cover for commercial clients. We also work in London, around 20 miles away.
Every address in SL3 is within our area for extract fan repair, from the main roads to the quietest streets. Whether your site is on Fulmer Road, Alderbourne Lane and Hay Lane or a nearby road, our technicians can take on the work. If your site is just outside Fulmer, we cover Tatling End (1 mile north-east), Wexham Street (1 mile south-west), Gerrards Cross (1 mile north), Stoke Poges (2 miles south-west) and Rush Green (2 miles east). Further out, we also cover Slough (4 miles south-west), Cippenham (5 miles south-west), Chalvey (4 miles south-west), Britwell (3 miles south-west), Langley (4 miles south) and Upton (4 miles south).
Local landmarks in Fulmer
Around Fulmer, our work takes us to kitchens and buildings near Bulstrode Park, The Black Horse Public House and Khalsa Secondary Academy, among other places. The closest station to Fulmer is Gerrards Cross station, about 1.9 miles north of the centre. Other landmarks nearby include British Airways Heritage Collection (3.5 miles south-east) and Wexham Park Hospital (2.2 miles south). Not far away are Horse Shoe Bay and Stoke Common.
Questions from Fulmer
Is there an emergency callout for extract fans in Fulmer?
Extract fan emergencies in Fulmer are covered around the clock. Phone 0345 646 2711 and we’ll talk through the fault and access. Tell us where the fan is and how to reach it.
Do you work at weekends in Fulmer?
Yes, evening, overnight and weekend work is normal for us. The site is handed back ready to open. When you phone us on 0345 646 2711, or email photos, mention when the site is quiet.
How much does an extract fan repair cost?
The cost depends on what’s wrong and how easy the fan is to reach. After diagnosing, you get a fixed quote before any work starts.
What does TR19 mean?
TR19® is BESA’s specification for ventilation hygiene. TR19® Grease, a standalone specification since 2019, covers grease in kitchen extract systems, and TR19® Air covers general supply and extract systems.
Who is the responsible person?
The law calls them the responsible person. That is generally the employer or the person in control of the premises, and in shared buildings more than one person can have duties. Your lease and fire risk assessment should make it clear.
Can you supply and fit a replacement fan?
We can. We fit replacement fans as well as repairing old ones, and we’ll explain the options.
Which sectors do you work in?
Commercial premises of every kind: from restaurants, pubs and hotels to schools, hospitals, care homes, offices, shops and food production sites. Work is timed around how each site runs.
Which accreditations do you hold?
Duct Doctor is a BESCA Vent Hygiene Elite member, cleaning to BESA TR19® Grease. We also hold CHAS, SafeContractor and ISO 9001, and we’re fully insured.
Different parts, different methods
Belt-driven fans
In a belt-driven fan, the motor drives the impeller by belt. Belts wear, stretch and slip, so we check the pulleys and bearings as well.
Fan controls
Supply faults are a job for an electrician. If that’s the cause, we will say so and explain what we found.